according to test requirements such as BS Pt. 2 or ISO This can be expressed in two ways, the Coefficient of Friction µ and the Torque Coefficient (K . ISO FASTENERS – TORQUE/CLAMP FORCE TESTING. DIN EN ISO Fasteners – Torque/clamp force testing (ISO + Amd ) (includes Amendment).
|Published (Last):||15 January 2007|
|PDF File Size:||6.14 Mb|
|ePub File Size:||14.93 Mb|
|Price:||Free* [*Free Regsitration Required]|
In practice, tightening instructions often specify fitting fasteners with a specific torque. Webprint Printed and bound. In this process the fasteners are screwed to their own washer. The friction between roughened surfaces is greater than between smooth ones. Standards Subscriptions from ANSI provides a money-saving, multi-user solution for accessing standards.
If the factor is very high, fasteners need to be tightened with isk high torque and the efficiency of the fasteners decreases. We have capability to collect time synchronized data across multiple instruments and sensors including the following:.
BS EN ISO +A – Fasteners. Torque/clamp force testing
Eddy current method phase sensitive. Not only can FEA show where new parts may have potential issues, it can be used to diagnose failures seen in the field, and also to optimize designs in order to reduce cost.
Have fun clicking through! It can also be used in conjunction with FEA when a transfer of fluid causes a resultant force that needs to be considered when doing structural isp.
This standard also specifies how these coefficient of friction levels can be calculated. Your Alert Profile lists the documents that will be monitored. The option of choosing between uncoated and galvanised bases reflects the prevailing procedures in the American and European areas. This will give you increased confidence in your fastener designs and manufacturing processes.
Cross-cut test for adhesion. If fasteners are lubricated, friction is reduced — this applies both with regard to both external lubrication via grease or wax and integrated lubrication via the addition of a lubricant to the coating.
Please first verify your email before subscribing to alerts. Username or email address: Based on this data, the nut factor or total coefficient of friction can be calculated and used to evaluate the effect of various fastener finishes, coatings, lubricants and manufacturing processes.
These include the geometry of the screw and 16074 friction between fastener and components. If you need to be able to add standards to the monitoring service, you must register as a user with your own username and password. Coefficients of friction cannot be specified using measurement technology. A bolt that requires testing is screwed into the test bench and fixed with a reference bolt. Such data can be used to establish the appropriate torque-angle requirement for the specific fastener and joint.
Because if bolts and screws are too loose, components may move. For hard bases the standard prescribes a narrow range of hardness, but permits a broad range of hardness for soft bases. This technique has a distinct advantage because the actual joint and fastener uso be tested without compromising the joint stiffness through the introduction of a load cell.
You can download and open this file to your own computer but DRM prevents opening this file on another computer, including a networked server. You may delete a document from your Alert Profile at any time.
The benefits of a subscription: Want to learn more and discuss your project? As a result, the coefficients of friction calculated from torque and clamp force only really apply to the conditions on the test bench. Already Subscribed to this document. Every day, thousands upon thousands of screws and bolts are used to fasten components together. With these fasteners a washer is threaded onto the blank; the subsequent cold forming in which the thread is rolled into the surface ensures that this washer cannot fall off.
The respective complementary partial 10647 can be identified via subtraction. The objective is to fix components to each other in a way that enables 61047 to fulfil their function.
This ensures that you are always up-to-date and saves you both time and money. MEC can be perform tests on actual fastened assemblies to obtain torque-angle graphs and to establish the torque to reach the yield strength of the bolt. If the document 16407 revised or amended, you will be notified by email. Add to Alert PDF. That may sound routine initially. You need to log in before adding standards to the monitoring service.
However, specialists also take a closer look.