ORG. GND. 8-lead SOIC. 8-lead dBGA2. 8-lead PDIP. 8-lead SOIC. Rotated (R). ( 1K JEDEC Only). 8-lead mini-MAP (MLP 2×3). 8-lead TSSOP. DO. DI. NC. VCC. CS. SK. 1. 2. 3. 4. 8. 7. 6. 5. GND. Normal. Pinout. Rotated. Pinout .. 93C Address bits pattern -> User defined. Timing Diagrams. Address. 8-lead SOIC. 8-lead dBGA2. 8-lead PDIP. 8-lead SOIC. Rotated (R). (1K JEDEC Only). 8-lead Ultra Thin mini-MAP (MLP 2×3). 8-lead TSSOP.

Reasonable quantity of this product can be available within 3 working days.

Maybe it is rotated, did you check on what pin is gnd? Yes I have had CDH gear for about 15 yearsthe first interface i had had a sine wave generator for doing the early Philips radio’s with ER Device search Fulltext search Supported devices.

For the proper functioning of this website we recommend to turn on JavaScript. Blank A B C. BeeHive8S discontinued Direct connection.

L46 - SO8 EEPROM with rotated pinouts used in japan car electronic

Rotatr Electronics - http: My CDH Electronics gear has thrown it’s teddy out of the pram again, and has to go back to see Colin, so I’m trying to read it with an Asix Presto, I wired it up as a rotated 93c46 and was unable to read, so tried as a normal one still the same.

The names of the chips in our database contain all characters necessary for identification of the device, but don’t contain such codes, that have no influence to the programming, for example temperature code rottae, speed codepacking type codeetc.

Therefore we can return your samples only if we get chips from semiconductor manufacturer. Would I have damaged it if it was not rotated, and I read 93f46 as rotated. Read with a LV48 programmer.

MEMprog discontinued Direct connection.

Any help would be appreciated. Move the cursor over the box to highlight particular section. IT yes, they are: Before years i tryed to read one rotated chip as 9c346, more than times and ofcourse i did’n read it, then i ask a friend and he say that maybe it is rotated and i tryed it like rotated and read it sucsessfull, so 93cc46 was not problem. Device Search tip The names of the programmable devices in our database don’t contain all charactersshown rotaet the top of the chip or mentioned in a datasheet section part numbering.

Thanks MH, I think I will have to do that, sorry about your programmer, if it’s the one I think it is, there is only a handful of components on the board, cant you find out what’s faulty, or are you getting them replaced under warranty?

It was rotated, refitted it and radio now says error 3, so I think I have buggered it one way or the other, Still works if you hold down the band button and turn it on but it beeps all the time. This number indicates quantity of items that could be produced from components in stock. If gnd on radio is on pin5 on pcb, rotwte chip is normal, if gnd is on pin7 on pcb, so chip is 93c446.

Device: 93C46

I do not use it very often, 93f46 and every time I do I have to remove the token and then re-install the software. T51prog2 discontinued Direct connection. MEMprogL discontinued Direct connection. Thanks for the info on the 93c PIKprog2 discontinued Direct connection.

They are going up as rotatee if you look at later listings by the same seller they are more expensive. MEMprog2 discontinued Direct connection.

allprog_lista | Allprog

The real chips are also necessary to have in the case of reproducing issues from the created support. Last time I tried it would not re-install, and so I am sending it back for later software to be added.

In case of missed samples, we always asking the semiconductor manufacturer for samples, but if samples are not available - also in the package you’re asking for the support - the solution from us will be 93cc46.

If such code letter is at the end of the name, it should be omitted. The sample of programmable devices is necessary to have for test and release new chip support.